99 Nissan Altima incorrect info

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • MasterWrench
    Senior Member
    • Oct 2006
    • 1186

    99 Nissan Altima incorrect info

    VIN#1N4DL01D0XC105100 2.4 4cylinder Automatic...

    When in the info section testing ICM there is no info for 4 cylinder, only 6 cylinder...

    MODIS 8.2
    MasterWrench
  • Matt_yz450f
    Snap-on Product Support Specialist
    • May 2008
    • 60

    #2
    Hey MasterWrench,

    So I'm looking at this here and when I id it in I'm not sure I'm fallowing where your at? on the Modis are you under Component Testing? and then "ICM(POWER TRANSISTOR)? Or are you actually under the scanner area of the tool where you ID the car in? if you can give me an example ie:Component Testing>New Veh ID>US IMPORT>NISSAN>FUEL INJ>1999>ALTIMA>ICM(power transistor)>Component Info>"there is no selection for 4 Cyl"

    seems like a lot of work but its going to point me in the exact area where you are at so I can look in to this.

    Thanks,

    Matt
    Product Support Specialist
    Snap-on Diagnostics

    Comment

    • MasterWrench
      Senior Member
      • Oct 2006
      • 1186

      #3
      Nissan, fuel injection, 1999, Altima, Component Tests, ICM(Power Transistor), all of the info is for 6 cylinders.

      Seems like it is missing a menu to select the engine size???
      MasterWrench

      Comment

      • Matt_yz450f
        Snap-on Product Support Specialist
        • May 2008
        • 60

        #4
        ok, got it, I was looking and I saw that it shows the info but I didn't know that it was only for a 6cyl, I'll go ahead and wright this up and get it over to engineering. Thank you for the info.

        Thanks again,

        Matt
        Product Support Specialist
        Snap-on Diagnostics

        Comment

        • Matt_yz450f
          Snap-on Product Support Specialist
          • May 2008
          • 60

          #5
          ok sir, after submitting that, it came back to me that the info in there is only for a 4cyl 2.4L because they don't make a 6cyl altima in that year. so the info in the component testing is correct.

          Matt
          Product Support Specialist
          Snap-on Diagnostics

          Comment

          • MasterWrench
            Senior Member
            • Oct 2006
            • 1186

            #6
            If you go into the tests the connector pin out is for a 6 cylinder in ICM I'll upload some screen shots for you in a bit....
            MasterWrench

            Comment

            • Matt_yz450f
              Snap-on Product Support Specialist
              • May 2008
              • 60

              #7
              that would be great thanks!
              Product Support Specialist
              Snap-on Diagnostics

              Comment

              • MasterWrench
                Senior Member
                • Oct 2006
                • 1186

                #8
                here ya go....
                Attached Files
                MasterWrench

                Comment

                • Matt_yz450f
                  Snap-on Product Support Specialist
                  • May 2008
                  • 60

                  #9
                  OK I got it, I see what you are looking at, thanks I resubmitted my request and this one will go through better. I lead them to the wrong spot, this one will lead them to the right spot and if I get any word back I'll let you know.

                  Thanks for the information,

                  Matt
                  Product Support Specialist
                  Snap-on Diagnostics

                  Comment

                  Working...